Devices You Need to Install a New Bathtub
Devices You Need to Install a New Bathtub
Blog Article
The publisher is making several good pointers about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this article further down.
Setting up a tub isn't exactly rocket science, however it does need solid plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably tough project. If the old bathtub is easily available, the task can relocate quickly; if you need to open up a wall to get rid of the old tub as well as position the brand-new tub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will need an assistant to leave the old bathtub as well as set in the brand-new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is better to take into consideration using one before you start. Chances are you might need an expert plumber to make tube links.
This short article will certainly help you set up a new tub in your washroom if you have currently purchased a new tub and also don't need to transform the arrangement of your previous water system pipelines.
Your tools and also material checklist must comprise the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is separate the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of getting rid of the existing faucets can be quite troublesome because of the limited access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have actually been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this process. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washing machines remain in area between the tap as well as the sink. Protect the tap in place with the producer offered backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical tap ports. The former type ought to be linked to the tap ends first, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, position the tub in the needed position. The wooden boards are useful in evenly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little points.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bathtub till the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the supply of water and examine all joints as well as new pipework for leakages as well as tighten them if essential. Fill up the bathtub and additionally check the overflow electrical outlet and the regular outlet for leakages.
Finally, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling and also securing around the bathtub must wait till the bathtub has been utilized at the very least once as this will resolve it right into its final setting.
Planning for the Installment
Firstly, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its final position.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bath and the tiling, leading to complications with dampness and possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the bath tub with water before sealing, to allow for the activity experienced when the bathtub remains in usage. The sealer can split fairly very early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily available on the marketplace. It is recommended to fit the tiles using waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted person who reads about Installing A Bathtub, I figured sharing that excerpt was really useful. Loved our content? Please share it. Help other people find it. Thanks a lot for your time. Kindly check up our site back soon.
Instant Quote
Report this page